Kenmore Dishwasher Wheels and Rollers
Popular Kenmore Dishwasher Wheels and Rollers
42% OFF
Your Price
$26.89
$46.00
In Stock
Kenmore Dishwasher Lower Dishrack Wheel
PartSelect Number PS3406971
Manufacturer Part Number W10195416
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Thomas from WEST OLIVE, MI
Broken wheel unit on the bottom dish rack
All you do is pop out the old wheel unit at two (2) points on the plastic wheel housing and pop in the new one. Easy fix. Less than a 5 minute fix.
Read more...
Kenmore Dishwasher Lower Dishrack Wheel Assembly
PartSelect Number PS11750057
Manufacturer Part Number WPW10195417
This gray plastic lower dishrack roller is a part for your dishwasher. It attaches to the bottom of the lower dishrack, allowing it to move in and out smoothly. If the lower dishrack stops moving in and out easily or preventing you from being able to shut the dishwasher door, inspect the dishrack roller for damage. The assembly includes 2 rollers and the bracket that attaches to the dishrack (parts are not sold separately). This assembly is sold individually, so you will need 4 assemblies to replace them all in your appliance. For this easy repair, start by removing the lower dishrack from the appliance and set it on the counter. Use a screwdriver to pry off the old roller assembly from the lower tabs. Align the new part on the dishrack by snapping it in place.
Fixes these symptoms
- Door latch failure
- Door won’t close
- See more...
Installation Instructions
Barbara from BETHESDA, MD
One of the rollers broke of on the lower dish rack
Snapped the old one off and snapped the new one on.
Read more...
Kenmore Dishwasher Dishrack Roller - Grey
PartSelect Number PS8727387
Manufacturer Part Number 00611475
This is a replacement dishrack roller or wheel for your dishwasher. It is made of gray plastic, measures a little over an inch in diameter, and is sold individually. This roller is designed for the lower dishrack of your dishwasher. On one side of the roller is a clip that allows it to be attached to the dishrack. The dishrack roller allows you to slide the dishrack in and out of the dishwasher efficiently. If one of the rollers is broken or missing, it can cause the dishrack to become difficult to slide in and out. To replace the roller, simply snap it off the dishrack, and snap the new one into place. This is a genuine OEM part.
Installation Instructions
Dennis from PLEASANTVILLE, NJ
Kenmore Dishwasher Rack Roller Wheel
PartSelect Number PS8727423
Manufacturer Part Number 00611666
This wheel is a dishwasher rack wheel designed for the upper rack of your appliance. The roller wheel is approximately 1.25 inches in diameters and includes the brushing you need for installation. It simply clips right on to the rack frame. After the wheel are attached to the side of the dishrack and are placed into the slides on either side of the appliance. Dishrack roller wheels allow the upper rack in a dishwasher to glide in and out of the appliance with ease. Due to the fact the roller wheel is made of plastic they tend to wear out after a period of time, also they can break. We do recommend you replace these rack wheels in pairs as they often wear out at the same rate. These wheels are sold individually.
Installation Instructions
Catherine from AMHERST, NY
The plastic clip on the roller broke
We let this go for a shameful amount of time before I decided I could probably fix it. The roller broke so you could only pull it out about halfway or it would come off the track. I looked up the part, and bought it. Actually bought two in case it happened again. When I arrived I looked at how it was put together on the other side and then just basically pushed it onto the rod and it was fixed. I am ashamed it took so long to do it. Never be afraid to try it yourself. It was a total of $10 shipped to fix it.
Read more...
Your Price
$29.89
In Stock
Kenmore Dishwasher Lower Rack Wheel Kit - 8 Pack
PartSelect Number PS11726733
Manufacturer Part Number WD35X21038
This lower rack wheel kit includes 8 wheels and 8 axles that allow the lower dishwasher rack to slide in and out smoothly. If your dishwasher door will not close, is noisy when operating, or the dishes are not cleaning properly, you might need to replace one or more of the wheels. Each wheel and axle are made of plastic, and fit into one another so they can be clipped on to the lower dishwasher rack. Many of our customers found this repair to be quick and easy, and the only tool you should need to complete the repair is a pair of pliers.
Fixes these symptoms
- Door won’t close
- Leaking
- Noisy
- See more...
Installation Instructions
Mark from Huntingdon Valley, PA
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Read more...
Kenmore Dishwasher Upper Dish Rack Wheel Mount
PartSelect Number PS11745459
Manufacturer Part Number WP8268743
This upper dish rack wheel mount can be used on either side of your dish rack. It is sold individually. The part includes the wheel and support, which attaches to the dish rack and allows it to slide in and out easily.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Noisy
- See more...
Installation Instructions
Jason from Todd, NC
Worn dishrack wheel mount
This wheel mount broke from normal use and made the upper dish rack disconnect from the sliding arm that extends it outside the dishwasher body so that you can fill it. The part was delivered quickly and was easy to install using just a screwdriver to loosen the retainer clip on the end of the extension slide. Once the retainer clip was removed, the new part was slid into place and clipped onto the rack. The install was complete.
Read more...
Your Price
$29.36
In Stock
Kenmore Dishwasher Upper Rack Wheel with Mount
PartSelect Number PS11745451
Manufacturer Part Number WP8268655
This is a replacement upper dish rack wheel with mount for your dishwasher. The mount supports the dish rack, and the wheel allows the rack to slide out easily. To replace this part, remove the rack stops and pull out the upper dish rack. This wheel mount pops off, and the new one can be snapped into place.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Noisy
- See more...
Installation Instructions
James from Gulfport, MS
The wheels on the upper dish rack broke
I removed the end caps on the slides with needle nose pliers, removed the old wheels and installed the new ones, then I snapped the slide end caps back on. Super responsive service from PartSelect.com Thanks!
Read more...
Your Price
$11.09
In Stock
Kenmore Dishwasher Rack Adjuster
PartSelect Number PS11750255
Manufacturer Part Number WPW10204131
This OEM dishrack roller and adjuster is found in your dishwasher. They work together to support and facilitate the smooth movement of your dishrack. The dishrack rollers are small wheels located on the sides of the dishrack and allow it to slide in and out effortlessly. Meanwhile, the dishrack adjuster is used to adjust the height via the selector at the back of this component. Over time, the rollers wear out. You may experience resistance or difficulty when sliding the dishrack in or out. If left unreplaced, your rollers or adjuster may break, causing dishes to tilt, collide, or fall over during the wash cycle. When removing a roller and adjuster from your appliance, you will need to pull out the dishrack partway. Detach the assembly by depressing the tabs on the two end stops before lifting them up. Keep in mind that the roller and adjuster are sold together, but the dishrack itself is sold separately.
Installation Instructions
Randy from Glenview, IL
Replacement of broken Rack Assembly Mount with Wheel
The only piece that may be a little difficult to remove here without a tool is the 'Track Stop'. This piece has a couple of clip-like pieces that need to be depressed in order to remove it. A flathead screw driver will do the trick. Once this piece is out and you have popped the Mount off of the Rack, you simply roll the piece out of the track, roll the new one in and snap the new Mount in place, replacing the Track Stop when you are done. VERY EASY!
Read more...
Your Price
$11.29
In Stock
Kenmore Dishwasher Upper Rack Wheel and Mount Assembly
PartSelect Number PS11745525
Manufacturer Part Number WP8270019
Sold Individually.
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
Kevin from Hurst, TX
top dw rack fell off of rollers
Amazingly, this not-too-old dishwasher's plastic parts that hold the top rack onto the sliders became brittle (a real design flaw, in my opinion) and the tabs that held the rollers in place all broke off. With the right parts and the great instructions on this site, the repair was fairly easy and we saved a lot of $$ by not having to call for service. Just follow the instructions...
Read more...
Kenmore Dishwasher Upper Rack Roller
PartSelect Number PS11753471
Manufacturer Part Number WPW10350401
This assembly is the wheel and the mount for your upper dishrack. Sold individually. This is an authentic OEM part for use with Whirlpool, KitchenAid, Kenmore and Jenn-Air Dishwashers. The dishrack wheel lets you roll the rack easily on the support rails. This part is sold individually. The most common reason for replacing the dishrack wheel is if it breaks causing the rack to jam. The tool that you will need to replace the dishrack wheel is a flathead screwdriver.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Richard from TRUCKEE, CA
Fully loaded top rack would detach from track when pulled out for emptying.
Removed dishwasher from cabinetry to replace tub rollers (4). Replaced roller sets (4) on top rack. Also replace both rails and rail stops. Screwdriver was only tool required for this part of repair. Needed wrench and screwdriver to remove and replace dishwasher in lower cabinetry.
Read more...
Related Kenmore Dishwasher Parts
- All Kenmore Dishwasher parts
- Kenmore Dishwasher Brackets and Flanges
- Kenmore Dishwasher Caps and Lids
- Kenmore Dishwasher Circuit Boards and Touch Pads
- Kenmore Dishwasher Dishracks
- Kenmore Dishwasher Dispensers
- Kenmore Dishwasher Doors
- Kenmore Dishwasher Ducts and Vents
- Kenmore Dishwasher Elements and Burners
- Kenmore Dishwasher Filters
- Kenmore Dishwasher Grilles and Kickplates
- Kenmore Dishwasher Handles
- Kenmore Dishwasher Hardware
- Kenmore Dishwasher Hinges
- Kenmore Dishwasher Hoses and Tubes
- Kenmore Dishwasher Insulations
- Kenmore Dishwasher Insulations
- Kenmore Dishwasher Knobs
- Kenmore Dishwasher Latches
- Kenmore Dishwasher Legs and Feet
- Kenmore Dishwasher Motors
- Kenmore Dishwasher Panels
- Kenmore Dishwasher Pumps
- Kenmore Dishwasher Racks
- Kenmore Dishwasher Seals and Gaskets
- Kenmore Dishwasher Sensors
- Kenmore Dishwasher Spray Arms
- Kenmore Dishwasher Springs and Shock Absorbers
- Kenmore Dishwasher Switches
- Kenmore Dishwasher Thermostats
- Kenmore Dishwasher Timers
- Kenmore Dishwasher Valves
- Kenmore Dishwasher Wire Plugs and Connectors