Kenmore Dishwasher Caps and Lids
Popular Kenmore Dishwasher Caps and Lids
Your Price
$7.28
In Stock
Kenmore Dishwasher Stop Clip
PartSelect Number PS11770481
Manufacturer Part Number 5304506510
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete it you only need a flat blade screwdriver. Use the screwdriver to pry the locking tab open on the cap, located at the front of your upper dishrack. Pull off the end cap and lock the new one into place.
Installation Instructions
Bobby from Austin, TX
Broken wheels, Caps and Brackets. Couldn't hold dishes or wash right.
Just use a hexagonal driver to remove the Upper rack roller, screw the new ones in, place caps on the rail ends, and pop the new wheel on with some pliers! Simple and fun!
Read more...
Your Price
$27.56
In Stock
Kenmore Dishwasher Rinse-Aid Dispenser Cap
PartSelect Number PS11746426
Manufacturer Part Number WP8558307
The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there could be an issue with the rinse aid cap. Check the cap and its gasket for any damage or melting. If the cap has melted or it is not sealing the dispenser properly, the part should be replaced right away. This rinse aid cap comes with the gasket, so you should discard the existing gasket and rinse aid cap at the same time. The repair is relatively straightforward, and requires no tools.
Fixes these symptoms
- Door latch failure
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
James from Mesquite, TX
Cap came off and melted
Opened door and installed cap. Not much effort. But really got good service from Parts Select. Received order much faster than I had expected.
Read more...
Your Price
$19.95
In Stock
Kenmore Dishwasher Rinse Aid Cap
Thank you for stocking the parts and shipping them as promised. Read more...
PartSelect Number PS421128
Manufacturer Part Number 154388801
This is a replacement cap for the detergent/rinse aid dispenser. If the rinse aid cap is damaged or missing, you may notice too much rinse aid in the dishwasher. The cap simply screws into the dispenser, so if your cap is damaged you can simply screw it out, then screw in the new one. The rinse aid cap is approximately 2 inches in diameter and is sold individually. This is an OEM part, directly from the manufacturer.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
Jeffrey from Mildland, MI
Striker
Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple. Thank you for stocking the parts and shipping them as promised. Read more...
Kenmore Dishwasher LID
PartSelect Number PS8727344
Manufacturer Part Number 00611322
Fixes these symptoms
- Not draining
- See more...
Kenmore Dishwasher Tub Cap
PartSelect Number PS11703426
Manufacturer Part Number W10795980
The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Royce from GREENSBORO, NC
Dish rack slide arms losing ball bearings
Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!
Read more...
Your Price
$18.39
In Stock
Kenmore Dishwasher Rinse Aid Fill Cap
PartSelect Number PS2351824
Manufacturer Part Number WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
ANNE from SWANNANOA, NC
Lost Despenser Lid, Droped It And Havent Seen It Since.
Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.
Read more...
Your Price
$11.09
In Stock
Kenmore Dishwasher Rinse Aid Cap
PartSelect Number PS11741341
Manufacturer Part Number WP3378134
This cap does not require the use of an O-ring seal. The wet agent assembly cap is clear in color and made of plastic. This is a part for your dishwasher. This part may need to be replaced if you notice that your dishwasher is not dispensing detergent, cleaning dishes properly, or has sprung a leak. The cap is found on the inside of your dishwasher door. This is an extremely simple repair that requires no tools. Simply open your dishwasher door, twist the old cap out of place, ensuring no pieces are left behind. Screw your new cap into place.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
Louis from Niceville, FL
Water dripped out from the bottom of door.
Diagnosing the problem, i.e. finding the source of the leak, was the hardest part. The best clue was the leak only occurred well into the cycle when the water was hot and steam was coming out the vent. I then assumed there was a bad seal and steam & condensed water was leaking down into the door. I replaced the vent duct & seal, a broken drip cover (an internal part in the door), and replaced a missing rinse aid cap. This stopped the leak.
Read more...
Kenmore Dishwasher Rinse Aid Cap
PartSelect Number PS11746567
Manufacturer Part Number WP8564929
This rinse aid cap or fill cap is for your dishwasher and it screws into the jet dry dispenser. Sometimes the cap can become loose and fall out, which can cause it to melt from the heater. If your cap is damaged or missing, this is the part you will need to replace it. It is made of white plastic and is a little more than an inch in diameter. This rinse aid cap is sold individually.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
Joan from Glendora, NJ
the rinse aid cap fell into the bottom of the dishwasher and got burnt by the coils. It was letting the rinse aid empty out every time I used the dishwasher because the seal was broken.
I just put the new cap on and that was it.
Read more...
Kenmore Dishwasher LID
PartSelect Number PS8697157
Manufacturer Part Number 00166623
This OEM-sourced detergent dispenser cover, also known as a rinse aid dispenser lid, seals and protects the detergent compartment in your dishwasher. Typically located on the inner door, it covers the detergent dispenser assembly. When loading the dishwasher, you lift the cover to add rinse aid before running a cycle. If the detergent dispenser cover is broken, you may notice visible cracks, chips, or it may not stay in place properly. If left unreplaced, it can result in detergent leakage during the wash cycle. To remove the cover, first, turn off the power and water supply. Open the dishwasher door and gently insert a flathead screwdriver between the dispenser body and the cover, prying it off. When installing the replacement cover, align it at an angle with the housing and fit one side in before rotating it to snap into place.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Sue E from CARMEL, IN
Rinse aid dispenser lid would not stay closed
Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.
Read more...
Kenmore Dishwasher Dispenser Cap
PartSelect found just the cap I needed at a much better price.
Fantastic service. Shipping was faster than promised. I can't say enough good things about them! Read more...
PartSelect Number PS11746156
Manufacturer Part Number WP8533380
This is the cap for your rinse aid dispenser.
Fixes these symptoms
- Leaking
- Not drying dishes properly
- See more...
Installation Instructions
Brian from Marion, IA
Couldn't find the part anywhere, but...
PartSelect found the right part for me on the first try. I had scoured the web looking for this particular drying agent cap. Even Sears said I'd have to order the entire dispenser assembly - $$$!PartSelect found just the cap I needed at a much better price.
Fantastic service. Shipping was faster than promised. I can't say enough good things about them! Read more...
Related Kenmore Dishwasher Parts
- All Kenmore Dishwasher parts
- Kenmore Dishwasher Brackets and Flanges
- Kenmore Dishwasher Circuit Boards and Touch Pads
- Kenmore Dishwasher Dishracks
- Kenmore Dishwasher Dispensers
- Kenmore Dishwasher Doors
- Kenmore Dishwasher Ducts and Vents
- Kenmore Dishwasher Elements and Burners
- Kenmore Dishwasher Filters
- Kenmore Dishwasher Grilles and Kickplates
- Kenmore Dishwasher Handles
- Kenmore Dishwasher Hardware
- Kenmore Dishwasher Hinges
- Kenmore Dishwasher Hoses and Tubes
- Kenmore Dishwasher Insulations
- Kenmore Dishwasher Insulations
- Kenmore Dishwasher Knobs
- Kenmore Dishwasher Latches
- Kenmore Dishwasher Legs and Feet
- Kenmore Dishwasher Motors
- Kenmore Dishwasher Panels
- Kenmore Dishwasher Pumps
- Kenmore Dishwasher Racks
- Kenmore Dishwasher Seals and Gaskets
- Kenmore Dishwasher Sensors
- Kenmore Dishwasher Spray Arms
- Kenmore Dishwasher Springs and Shock Absorbers
- Kenmore Dishwasher Switches
- Kenmore Dishwasher Thermostats
- Kenmore Dishwasher Timers
- Kenmore Dishwasher Valves
- Kenmore Dishwasher Wheels and Rollers
- Kenmore Dishwasher Wire Plugs and Connectors