General Electric Washer Timers
Popular General Electric Washer Timers
Your Price
$124.65
In Stock
General Electric Washer Timer
PartSelect Number PS4704240
Manufacturer Part Number WH12X10527
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
SURESHA from San Anselmo, CA
The dial under the knob that selects the washer settings stopped turning with the knob after just a few weeks
I had our reliable handyman take a stab at it after he determined what the issue was, and after we'd already tried a new knob and a new clip. Here's what he described as the issue: "Bottom line :the gears are to weak to take any force and break off. They need to be made of a strong metal not plastic. I also believe that the timer gear was binding and put more force on the gears."
Read more...
General Electric Washer Timer Dial
PartSelect Number PS269445
Manufacturer Part Number WH11X10015
This dial is located behind the timer knob.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Gordon from BLUE DIAMOND, NV
Timer knob broke off where the dial compression ring fits.
All I had to do was pull out the broken timer dial assembly and push in the new one.
Read more...
General Electric Washer Timer
Once the knob is off, remove the dial with the pointer on it and set it aside.
With this done, remove the three hex screws on the back of the control panel. Then lift the plastic control panel up, then forward. This will allow you to lay the control panel on the top of the machine.
Remove the wire harness by lifting up on the retainer and pulling on the harness. Grip the harness not the wires. The harness seats with a good grip so you'll need to work it a little.
Remove the single retaining screw that holds the timer unit to the control panel. Once the screw is removed TWIST the timer unit to remove it. The timer is held in place by two retaining "prongs" that you will break off if you try to pull the timer off the control panel. Once free of the retaining prongs, the timer is off the control panel and you are ready to replace with the new one.
Install is the reverse of what you just did.
When you get to putting the knob back on don't forget to put the dial with the arrow back on first. This only goes on one way but it takes a pretty good push to get it to seat. Next, put the nylon retaining clip on the knob such that it's barely on and slip the knob on the timer post only to the point where you see the slot in the knob and the slot on the post line up. When the two slots are aligned, use the blade of the flathead screw driver to push the nylon clip into place.
Reseat and align the control panel, replace the three screws, plug the unit back in and you can watch the game while the little lady gets back to her washing. :) Just kidding ladies.
This is an easy repair that anyone can do with only a couple hand tools and a little patience. Getting the knob off is the hardest part and a little finesse will work better than brute force.
Have fun, you can do it. Read more...
PartSelect Number PS1482382
Manufacturer Part Number WH12X10350
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Michael from Snellville, GA
Replace Timer Module
Remove the knob. This is the hardest part. To remove the knob, unplug the washer and pull the unit out so you can get to the back. Stand on the right side of the machine and pull the knob out. It is retained by a nylon clip. Take a small flathead screw driver and use it to push the clip up from the open ended side. Not much force is required. It will pop right up. The clip has a hook on one side so if you try to remove it with needle nose pliers (like I did the first time) you will bend the trim on the knob and likely break the clip.Once the knob is off, remove the dial with the pointer on it and set it aside.
With this done, remove the three hex screws on the back of the control panel. Then lift the plastic control panel up, then forward. This will allow you to lay the control panel on the top of the machine.
Remove the wire harness by lifting up on the retainer and pulling on the harness. Grip the harness not the wires. The harness seats with a good grip so you'll need to work it a little.
Remove the single retaining screw that holds the timer unit to the control panel. Once the screw is removed TWIST the timer unit to remove it. The timer is held in place by two retaining "prongs" that you will break off if you try to pull the timer off the control panel. Once free of the retaining prongs, the timer is off the control panel and you are ready to replace with the new one.
Install is the reverse of what you just did.
When you get to putting the knob back on don't forget to put the dial with the arrow back on first. This only goes on one way but it takes a pretty good push to get it to seat. Next, put the nylon retaining clip on the knob such that it's barely on and slip the knob on the timer post only to the point where you see the slot in the knob and the slot on the post line up. When the two slots are aligned, use the blade of the flathead screw driver to push the nylon clip into place.
Reseat and align the control panel, replace the three screws, plug the unit back in and you can watch the game while the little lady gets back to her washing. :) Just kidding ladies.
This is an easy repair that anyone can do with only a couple hand tools and a little patience. Getting the knob off is the hardest part and a little finesse will work better than brute force.
Have fun, you can do it. Read more...
General Electric Washer Timer
PartSelect Number PS3487294
Manufacturer Part Number WH12X10478
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
General Electric Washer Dryer Timer
PartSelect Number PS416776
Manufacturer Part Number 131062300
This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.
Installation Instructions
Bobby from Blue Ridge, TX
Timer would not shut dryer off.
A few screws out of the back of the top panel, pulled the dial off. Removed two more screws and the timer assembly came off. Then I just matched the color wires one at a time to the same spots on the new assmbly.
Read more...
General Electric Washer Timer
PartSelect Number PS269881
Manufacturer Part Number WH12X10152
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
General Electric Washer Timer
PartSelect Number PS269996
Manufacturer Part Number WH12X1083
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
Related General Electric Washer Parts
- All General Electric Washer parts
- General Electric Washer Agitators
- General Electric Washer Belts
- General Electric Washer Caps and Lids
- General Electric Washer Circuit Boards and Touch Pads
- General Electric Washer Dispensers
- General Electric Washer Drums and Tubs
- General Electric Washer Hardware
- General Electric Washer Hinges
- General Electric Washer Hoses and Tubes
- General Electric Washer Knobs
- General Electric Washer Latches
- General Electric Washer Motors
- General Electric Washer Panels
- General Electric Washer Power Cords
- General Electric Washer Pumps
- General Electric Washer Seals and Gaskets
- General Electric Washer Springs and Shock Absorbers
- General Electric Washer Switches
- General Electric Washer Valves