General Electric Washer Pumps

Popular General Electric Washer Pumps

Your Price
$44.89
  In Stock
General Electric Washer Pump Drain Assembly
★★★★★
★★★★★
74 Reviews
PartSelect Number PS12723115
Manufacturer Part Number WH23X28418
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Fixes these symptoms
Installation Instructions
Mike from NAPLES, FL
Washer ran fine but woudl not drain water - low humming noise
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Read more...
Your Price
$72.39
  In Stock
General Electric Washer Drain Pump and Motor Assembly
★★★★★
★★★★★
35 Reviews
PartSelect Number PS8768445
Manufacturer Part Number WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.
Fixes these symptoms
Installation Instructions
Gerald from Midlothian, VA
Washing Machine was not draining water from tub.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
Read more...
Your Price
$87.56
  In Stock
General Electric Washer Drain Pump
★★★★★
★★★★★
20 Reviews
PartSelect Number PS3654194
Manufacturer Part Number WH23X10043
This is a drain pump, designed to work with your washing machine. It expels water from your washing machine during the draining cycle. The most common reason for needing to replace this drain pump is if your unit is not draining properly, is leaking, or if your pumps are not spinning. This model is gray in color and is encased in plastic. It about 9 inches high, almost 6 inches long, and 4 inches thick.
Fixes these symptoms
Installation Instructions
James from WILLOW STREET, PA
would not empty the water
read about the problem ordered the part and then installed Read more...
Your Price
$139.96
  In Stock
General Electric Washer Drain Pump - 120V 60Hz
★★★★★
★★★★★
1 Review
PartSelect Number PS3501453
Manufacturer Part Number WH23X10040
Fixes these symptoms
Your Price
$238.72
  In Stock
General Electric Washer Motor and Drain Pump
★★★★★
★★★★★
13 Reviews
PartSelect Number PS1766031
Manufacturer Part Number WH23X10028
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.
Fixes these symptoms
Installation Instructions
Trent from Shreveport, LA
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test. Read more...
Your Price
$252.81
  In Stock
General Electric Washer Remote Style Pump with Motor
★★★★★
★★★★★
2 Reviews
PartSelect Number PS417325
Manufacturer Part Number 131268401
Use this with either a top load or front load washer. This pump has an horizontal mount.
Fixes these symptoms
Installation Instructions
Thomas from Walpole, MA
Pump Motor Failed
First, remove the 2 screws that hold the lower front cover in place, remove the cover and disconnect the plug and the ground wires from the pump. Next attach the washing machine drain hose to a wet vac, since even if the machine is empty, there will still be water in the outer tub and the pump. Suck the whole thing dry, remove the 2 bolts that hold the cover onto the pump, use a pliers to remove the 2 hose clamps, remove the hoses (no mess because of the vacuum). Remove the 2 screws that hold the pump to the base of the washer and remove the pump. Save the mounting bracket from the bottom of the pump. Orient the outlet on the new pump to match your old one if needed, instructions to do this are included with the new pump. Install the mounting bracket onto the new pump. Mount the pump to the washing machine base, reconnect the hoses, the cover and the wiring. Put the drain hose back into your drain. Run the machine, check for function and leaks. If all is well, replace the lower cover. Don't forget to tell your wife that the job was a whole lot harder than it looked. Read more...
Your Price
$82.77
  In Stock
General Electric Washer PUMP DRAIN
★★★★★
★★★★★
2 Reviews
PartSelect Number PS8757175
Manufacturer Part Number WH23X10051
This is a drain pump for your washing machine. This part funnels out water from the washing machine during the draining process of the cycle. This model is white and has a plastic shell. The drain pump is just over 4 inches high, about 5 inches long, and almost 3 inches wide. You will need to replace this part if your unit is leaking, and/or no longer draining water properly.
Fixes these symptoms
Installation Instructions
John from LYONS, CO
Drain pump failed
Remove back cover and with a light and a mirror the screws can be identified. Three hold this pump on. Remove electrical connection then the pump. So also remove the corrugated connecting boot by undoing three clamps. Clean and reassemble Read more...
Your Price
$128.02
  Special Order
General Electric Washer Drain Pump with Bracket - 220V
PartSelect Number PS756778
Manufacturer Part Number WH23X10019
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Fixes these symptoms
Your Price
$244.20
  In Stock
General Electric Washer Drain Pump with Motor
★★★★★
★★★★★
1 Review
PartSelect Number PS271331
Manufacturer Part Number WH23X10011
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Fixes these symptoms
Your Price
$666.21
  On Order
General Electric Washer PUMP COMPLETE
PartSelect Number PS271338
Manufacturer Part Number WH23X10018

Related General Electric Washer Parts