General Electric Washer Hardware
Popular General Electric Washer Hardware
Your Price
$9.96
In Stock
General Electric Washer Tub Bearing
I also power washed the basket and tub before reassembly.
The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.
The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.
I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.
I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.
The entire job took 5 hours. Read more...
PartSelect Number PS271509
Manufacturer Part Number WH2X1197
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a wash cycle. The most common reasons for needing to change your tub bearing is if your appliance is noisy or shaking/moving during the wash cycle, another common symptom is leaking water. This part is sold individually and measures to have an inner diameter of roughly 1 inch, and an outer diameter of roughly 2 inches.
Fixes these symptoms
- Leaking
- Will not agitate
- See more...
Installation Instructions
Wayne from Saint Augustine, FL
Tub seal leaked, rusted the transmission bearing which locked up
I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008. I also power washed the basket and tub before reassembly.
The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.
The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.
I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.
I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.
The entire job took 5 hours. Read more...
General Electric Washer SCREW
PartSelect Number PS417085
Manufacturer Part Number 131168200
Sold individually.
Installation Instructions
Glenn from Fort Worth, TX
Dryer squealed loudly
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst.
Read more...
General Electric Washer Screw
Removed belt from motor
Needed to lift up top of dryer
Inserted flathead screwdirver in front under top to push in two metal clips holding top down
Lifted up top of dryer
Removed 2 screws holding on front of dryer
Removed front of dryer
Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole.
Instead, I tried to remove the leads. This broke the fragile prongs.
Started dryer (with belt removed so drum doesn't spin)
Verified ignightor came on every heating cycle
Gas turned on properly
Gas turned off after 90 seconds
Gas never came back on
Indicitive of bad coils
New coils solved the problem
Replaced door switch and lint trap cover in the process. Read more...
PartSelect Number PS417463
Manufacturer Part Number 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Installation Instructions
Edward from Baltimore, MD
Drying too slowly
Removed access plate from back bottom leftRemoved belt from motor
Needed to lift up top of dryer
Inserted flathead screwdirver in front under top to push in two metal clips holding top down
Lifted up top of dryer
Removed 2 screws holding on front of dryer
Removed front of dryer
Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole.
Instead, I tried to remove the leads. This broke the fragile prongs.
Started dryer (with belt removed so drum doesn't spin)
Verified ignightor came on every heating cycle
Gas turned on properly
Gas turned off after 90 seconds
Gas never came back on
Indicitive of bad coils
New coils solved the problem
Replaced door switch and lint trap cover in the process. Read more...
General Electric Washer Screw 8-16 hxw 1/2 Stainless Steel
PartSelect Number PS258461
Manufacturer Part Number WD02X10067
Sold Individually.
Fixes these symptoms
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Farhan from EL DORADO HLS, CA
Spray arm fell off and melted due to screw loss
1. Unscrew the nozzle part from the dish rack and pull it down from the clip side. 2. Replace the new nozzle by inserting the plain side in first and clip it in. 3. Tighten the screw. 4. Insert the spray arm hole in the nozzle and tighten the screw with washer. 5. Start washing dishes
Read more...
Your Price
$25.92
In Stock
General Electric Washer Screw-In Plastic Leveling Leg
PartSelect Number PS1152204
Manufacturer Part Number 134548800
This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your appliance to make it leveled. This model is made entirely of plastic and is white in color. It is just under 2.5 inches long, 1.5 inches wide, and the head has a diameter of roughly 1.5 inches.
Installation Instructions
Sandra from Denton, TX
Stopped agitating versus level washer feet/leg
My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money.
Read more...
General Electric Washer SCREW
PartSelect Number PS3501388
Manufacturer Part Number WE2M302
Installation Instructions
Chris from WACO, TX
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
Read more...
Your Price
$19.21
In Stock
General Electric Washer Hub Nut
I also power washed the basket and tub before reassembly.
The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.
The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.
I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.
I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.
The entire job took 5 hours. Read more...
PartSelect Number PS271505
Manufacturer Part Number WH2X1193
This part is the hub nut, or lock down nut for your washing machine. It is designed to hold the inner tub on to the transmission. If your hub nut is stripped or damaged, it may need to be replaced. This hub nut is approximately 1.5 inches in diameter. This is an OEM part sourced directly from the manufacturer. You will need a hub nut wrench and some WD40 to loosen the nut and remove it from the agitator shaft.
Fixes these symptoms
- Leaking
- Will not agitate
- See more...
Installation Instructions
Wayne from Saint Augustine, FL
Tub seal leaked, rusted the transmission bearing which locked up
I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008. I also power washed the basket and tub before reassembly.
The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.
The agitator coupling kit contains a redesigned coupler and longer screw with new o-ring.
I bought the hub nut, split ring, tub bearing, agitator coupling kit and washer hub because these are all the parts that go on the transmission shaft. I felt it was best to spend a few dollars more to replace every part involved with the spin and agitation of the washer.
I used the channel lock and a hammer with a shortened handle to remove and replace the hub nut. Use caution as the nut is aluminum.
The entire job took 5 hours. Read more...
General Electric Washer Screw
PartSelect Number PS234226
Manufacturer Part Number WB1K5157
This screw is black in color and sold individually.
General Electric Washer Hub Nut
PartSelect Number PS3501416
Manufacturer Part Number WH01X10618
This hub nut is a genuine OEM replacement part for your stackable washing machine. Removing the hub nut may require a spanner wrench, as per the manufacturer specifications. Replacing this part requires some disassembly of the agitator assembly. The nut should be turned clockwise to remove it.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Lee from GRANDVILLE, MI
Tub seal leaking, grinding noise on spin.
Purchased spanner wrench for tub nut wouldn’t budge, impacted off. Then spin tub took 2days to get loose, lots of WD40 , also heated up center area, used a small sledgehammer head to hit a socket on the large part of the shaft . Had to take out outer tub to replace seal and support bearing unit.
Read more...
Related General Electric Washer Parts
- All General Electric Washer parts
- General Electric Washer Agitators
- General Electric Washer Belts
- General Electric Washer Caps and Lids
- General Electric Washer Circuit Boards and Touch Pads
- General Electric Washer Dispensers
- General Electric Washer Drums and Tubs
- General Electric Washer Hinges
- General Electric Washer Hoses and Tubes
- General Electric Washer Knobs
- General Electric Washer Latches
- General Electric Washer Motors
- General Electric Washer Panels
- General Electric Washer Power Cords
- General Electric Washer Pumps
- General Electric Washer Seals and Gaskets
- General Electric Washer Springs and Shock Absorbers
- General Electric Washer Switches
- General Electric Washer Timers
- General Electric Washer Valves